[Spread-users] Spread install question
Christopher Rasch
crasch at gmail.com
Mon Dec 11 18:29:16 EST 2006
Hi,
Executive summary:
I'm trying to install and run spread 3.17.4 (default spread.conf) on my
Powerbook G4 running Mac OS X 10.4.8 / Tiger. Whenever I try to run it
however, I get the following error:
[spread license info deleted]
Conf_init: using file: /Marketocracy/Configuration/spread.conf
Successfully configured Segment 0 [127.0.0.255:4803] with 1 procs:
localhost: 127.0.0.1
Finished configuration file.
Conf_init: could not get my ip address (my name is crasch)
Exit caused by Alarm(EXIT)
Anyone know what I should do to correct the problem causing this error
message?
" Conf_init: could not get my ip address (my name is crasch)
Exit caused by Alarm(EXIT)"
Thanks!
Chris
More details:
See attached system profile below if you want more details about my
environment. My machine's hostname is crasch, and the DHCP supplied IP
address is 192.168.1.116. I downloaded and installed the Spread
3.17.4.source distribution. Here's how I built and installed it:
./configure --with-zlib --with-ssl --with-openssl --without-apache
--without-apxs
make
make install
It appeared to build and install successfully.
I copied the sample.spread.conf file to
/Marketocracy/Configuration/spread.conf.
I then tried to launch spread as follows (as root):
/usr/local/sbin/spread -c /Marketocracy/Configuration/spread.conf
I got the following error message:
[spread license info deleted]
Conf_init: using file: /Marketocracy/Configuration/spread.conf
Successfully configured Segment 0 [127.0.0.255:4803] with 1 procs:
localhost: 127.0.0.1
Finished configuration file.
Conf_init: could not get my ip address (my name is crasch)
Exit caused by Alarm(EXIT)
The /var/log/spread log has this message:
[2006-12-06 17:35:32] Set user name to 'nobody'
[2006-12-06 17:35:32] Set group name to 'nogroup'
[2006-12-06 17:35:32] Finished configuration file.
[2006-12-06 17:38:20] Set user name to 'nobody'
[2006-12-06 17:38:20] Set group name to 'nogroup'
[2006-12-06 17:38:20] Finished configuration file.
[2006-12-06 17:38:20] Conf_init: could not get my ip address (my name is
crasch)
Exit caused by Alarm(EXIT)
Anyone know what might be causing this error? According to "Network
Preferences", my ip address is 192.168.1.116. The address is pingable:
crasch:~ crasch$ ping 192.168.1.116
PING 192.168.1.116 (192.168.1.116): 56 data bytes
64 bytes from 192.168.1.116: icmp_seq=0 ttl=64 time=0.118 ms
64 bytes from 192.168.1.116: icmp_seq=1 ttl=64 time=0.154 ms
64 bytes from 192.168.1.116: icmp_seq=2 ttl=64 time=0.113 ms
That's the address reported by ifconfig as well:
crasch:~ crasch$ ifconfig
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:11:24:45:bb:30
media: autoselect (none) status: inactive
supported media: none autoselect 10baseT/UTP <half-duplex>
10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,hw-loopback>
100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX
<full-duplex,hw-loopback> 1000baseT <full-duplex> 1000baseT
<full-duplex,hw-loopback> 1000baseT <full-duplex,flow-control> 1000baseT
<full-duplex,flow-control,hw-loopback>
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::214:51ff:fe7c:50c4%en1 prefixlen 64 scopeid 0x5
inet 192.168.1.116 netmask 0xffffff00 broadcast 192.168.1.255
ether 00:14:51:7c:50:c4
media: autoselect status: active
supported media: autoselect
fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078
lladdr 00:11:24:ff:fe:45:bb:30
media: autoselect <full-duplex> status: inactive
supported media: autoselect <full-duplex>
I searched for the error message, but the messages that came up in the
search did not lead to anything that fixed the problem. Any suggestions
for how I might go about debugging this problem further?
Thanks!
Chris
Hardware:
Hardware Overview:
Machine Name: PowerBook G4 17"
Machine Model: PowerBook5,9
CPU Type: PowerPC G4 (1.5)
Number Of CPUs: 1
CPU Speed: 1.67 GHz
L2 Cache (per CPU): 512 KB
Memory: 2 GB
Bus Speed: 167 MHz
Boot ROM Version: 4.9.6f0
Serial Number: W85452UBSX3
Sudden Motion Sensor:
State: Enabled
Network:
AirPort:
Type: AirPort
Hardware: AirPort
BSD Device Name: en1
Has IP Assigned: Yes
IPv4 Addresses: 192.168.1.116
IPv4:
Addresses: 192.168.1.116
Configuration Method: DHCP
Interface Name: en1
Router: 192.168.1.1
Subnet Masks: 255.255.255.0
IPv6:
Configuration Method: Automatic
DNS:
Domain Name: wp.comcast.net
Server Addresses: 68.87.76.178, 66.240.48.9
DHCP Server Responses:
Domain Name: wp.comcast.net
Domain Name Servers: 68.87.76.178,66.240.48.9
Lease Duration (seconds): 0
DHCP Message Type: 0x05
Routers: 192.168.1.1
Server Identifier: 192.168.1.1
Subnet Mask: 255.255.255.0
Proxies:
Proxy Configuration Method: Manual
ExcludeSimpleHostnames: 0
FTP Passive Mode: Yes
Auto Discovery Enabled: No
Ethernet:
MAC Address: 00:14:51:7c:50:c4
Media Options:
Media Subtype: autoselect
Built-in Ethernet:
Type: Ethernet
Hardware: Ethernet
BSD Device Name: en0
Has IP Assigned: No
IPv4:
Configuration Method: DHCP
IPv6:
Configuration Method: Automatic
Proxies:
Proxy Configuration Method: Manual
ExcludeSimpleHostnames: 0
FTP Passive Mode: Yes
Auto Discovery Enabled: No
Ethernet:
MAC Address: 00:11:24:45:bb:30
Media Options:
Media Subtype: none
Built-in FireWire:
Type: FireWire
Hardware: FireWire
BSD Device Name: fw0
Has IP Assigned: No
IPv4:
Configuration Method: DHCP
IPv6:
Configuration Method: Automatic
Proxies:
Proxy Configuration Method: Manual
ExcludeSimpleHostnames: 0
FTP Passive Mode: Yes
Auto Discovery Enabled: No
Ethernet:
MAC Address: 00:11:24:ff:fe:45:bb:30
Media Options: Full Duplex
Media Subtype: autoselect
Software:
System Software Overview:
System Version: Mac OS X 10.4.8 (8L127)
Kernel Version: Darwin 8.8.0
Boot Volume: Macintosh HD
Computer Name: crasch
User Name: Christopher Rasch (crasch)
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Picture 2.png
Type: image/png
Size: 75308 bytes
Desc: not available
Url : http://lists.spread.org/pipermail/spread-users/attachments/20061211/32e0b9d3/attachment.png
More information about the Spread-users
mailing list